Zircon MetalliScanner® MT 7 Pipe and Metal Detector
- Locate Rebar Pipes and other metals
- Detects ferrous and non-ferrous metals
- Detects metals in up to 15cm concrete*
- Back-lit screen
- Handle attachment included
- Includes battery and case
- Standard and DeepScan® modes
-
-
Information on the calibration of newly purchased equipment and what it means to you.
Calibration and its certification comes in varying forms on new equipment and in this section, we will break it down into the three areas that we use to classify calibration state at the point of purchase.
Manufacturers Calibration Certificate
This is a calibration certificate offered by the manufacturer supplied with the tester. This is also known as an end-of-line certificate or manufacturer’s certificate. These certificates vary depending on the manufacturer and product. They will not have your company's name on them and don’t always show proven test results.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
This instrument comes complete with the manufacturer's calibration certificate. Please be aware that these certificates are generic and may also be time-lapsed.
If you would prefer a personalised full traceable calibration certificate applied to the equipment before dispatch, then please select this option from the drop-down menu above, an additional calibration charge will apply.Manufacturers Certificate of Conformity
A manufacturer's certificate of conformity is not a calibration certificate. It is merely a statement that the equipment has been produced to operate within its intended application, it has no traceable certificate or constitutes any defined results for accuracy before leaving the manufacturing process.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
This instrument comes with a ‘manufacturer's certificate of conformity’. It is important to understand that this does NOT constitute a ‘calibration certificate’. A certificate of conformity merely states that the equipment has been designed and produced to meet the requirements of its intended application.
Where calibration of an instrument is possible we will offer this as a separately purchasable item and may be selected from the drop-down box above. You will be sent a full traceable calibration certificate produced in our laboratory and applied with your details as required.Personalised traceable calibration certificate from isswww
This is a calibration certificate created by us at ISS. This certificate is fully traceable to national and international standards. The certificate will show your company's details, tester information, proven test results and the equipment used to carry out the test. Nearly 90% of all calibrations we do are done in-house in one of our many fully equipped laboratories. You can add this service to your order on the product page before you checkout.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
We are on occasion able to offer FREE calibration on certain products at their point of sale (newly purchased equipment only) please look out for the following badge on the product's page to take advantage of this free offer.
-
-
Zircon MetalliScanner® MT 7 Pipe and Metal Detector
Zircon MetalliScanner® MT 7 metal detector quickly and easily locates rebar, pipes, and other metal before you saw or drill
Description
The MetalliScanner™ MT 7 electronic metal locator is designed for finding metal in standard residential, commercial, and industrial construction. The bright, backlit display indicates the metal target depth (in both inches and centimeters) up to 15 cm deep, the type of metal located (ferrous or non-ferrous), and whether you are moving towards or away from a target. This powerful tool saves time and money by eliminating guesswork, rework, needless holes, and costly broken drill bits or saw blades.
The MT 7 helps map the grid to avoid any metal, such as rebar, through any nonmetallic construction material, including concrete, tile and marble. Other recommended uses include locating and reinforcing rebar in masonry, measuring subsurface nail spacing in roofing material for compliance with building codes, and even detecting the nails/tacks in studs behind lath and plaster walls.
Key Features:
- Features two scanning modes; Standard mode and DeepScan® mode
- Locates and determines the depth of 1/2 in. rebar and 1/2 in. copper pipe up to 6 in. (15 cm) deep
- Finds and differentiates ferrous and non-ferrous metal
- Position accuracy to within ± 1/2 in. (13 mm) for #4 rebar or 1/2 in. copper pipe
- Backlit display and audio tone clearly indicate location of target
- Pivoting handle attachment for easier scanning and extended reach on the wall and floor
- Rubberized handle and built-in lanyard loop
- Includes 9V battery and protective carrying case
What is the difference between WireWarning® detection and AC Scan?
WireWarning® detection is a feature to alert the user to the presence of live, unshielded electrical AC wires while scanning for studs and metal. The WireWarning ® detection is always on in StudScan, DeepScan ®, or Metal Scan modes. (An LED light will flash, or a lightning bolt icon will appear on the LCD display when live AC voltage is present, depending on the model.)
AC Scan is a dedicated Scan mode on certain MultiScanner ™ tools that enables the user to narrow the location of live AC (using the interactive calibration technique). With AC Scan, the display changes to indicate when the tool is moving towards or away from the live electricity. This interface enables the user to adjust the tool’s sensitivity to live AC. This procedure can be repeated multiple times, as needed.
Caution: Electrical field locators may not detect live AC wires if wires are more than 2 inches from the scanned surface, in concrete, encased in conduit, present behind a plywood shear wall or metallic wall covering, or if moisture is present in the environment or scanned surface.
CAUTION: DO NOT ASSUME THERE ARE NO LIVE ELECTRICAL WIRES IN THE WALL. DO NOT TAKE ACTIONS THAT COULD BE DANGEROUS IF THE WALL CONTAINS A LIVE ELECTRICAL WIRE. ALWAYS TURN OFF THE ELECTRICAL POWER, GAS, AND WATER SUPPLIES BEFORE PENETRATING A SURFACE. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN ELECTRIC SHOCK, FIRE, AND/OR SERIOUS INJURY OR PROPERTY DAMAGE.
Always turn off power when working near electrical wires.
About Zircon
Zircon Corporation is an American company, established and operating in Northern California since 1975. Our commitment to designing and developing innovative electronic stud finders, metal detectors, and electrical scanners is unmatched. You might not expect a tool company to be headquartered in Silicon Valley. However, take a closer look and you’ll understand why.
| Key Features | Locate Rebar Pipes and other metals, Detects ferrous and non-ferrous metals, Detects metals in up to 15cm concrete*, Back-lit screen, Handle attachment included, Includes battery and case, Standard and DeepScan® modes |
|---|---|
| Product Stock Status | Next Day Delivery (subject to availability) |
| Manufacturer | Zircon |
Updated January 2024
Please note, our cut-off time is 2:00pm
Orders requiring calibration
Whilst we take the greatest care to get all orders dispatched and delivered to you in the stated time frame, orders received PM and requiring calibration may on occasion miss dispatch that day, according to the complexity of the calibration.Be assured they will ship on the next dispatch this in most cases should not add more than 24 hours to your delivery.
Bank/Public Holidays
Predicted delivery times are based on regular trading days Monday to Friday. Public holidays, bank holidays and weekends are outside the usual scopeof our dispatch and subject to activities/holidays of our carriers and therefore may incur additional days lead time to your order.
*UK Mainland (Revised March 2021)
| Service | Price |
| Standard FREE 2-3 Day Courier Delivery – UK Mainland only - Zones A & B - Order value OVER £75.00 ex VAT | FREE |
| Standard FREE 2-3 Day Courier Delivery – UK Mainland only - Zones A & B - Order value UNDER £75.00 ex VAT | £4.95 |
| Next WORKING Day (excludes Saturdays, Sundays and public holidays) – UK Mainland only - Zones A & B - ANY order value - Order by 2:00pm | £7.75 |
| Saturday ANYTIME Delivery - Order by 2:00pm | £9.95 |
Delivery Surcharges
Because of the high cost of carriage, we regretfully need to apply a surcharge on all deliveries made in the following regions:
- Zones A & B - Mainland delivery rates apply.
- Zone C - Scottish Highlands (Charges are calculated at the checkout).
- Zone D - Outer Hebrides, Orkney Isles, Shetland Isles, Isle of Man, Scilly Isles, and Channel Islands (Charges are calculated at the checkout).
- Zone E - Northern Ireland (Charges are calculated at the checkout).
- Zone F - Republic of Ireland (Charges are calculated at the checkout).
Offshore Services
All offshore deliveries are a 3-4 day service as standard. This includes Channel Islands, Northern & Southern Ireland, Scottish Islands, Isle of Man and the Scilly Isles.
International delivery
International delivery charges are automatically added to your order at the checkout. For any questions regarding international deliveries please contact us at sales@isswww.co.uk
Export
All export inquiries should be directed to the export division before placement of order.
If no shipping option is available to your selected country please call us FREE on 0800 0224 060 to discuss your requirements.
All stated prices are subject to VAT at the current rate where applicable.
E&OA