Socket and See Engineer Digital Multimeter
- True RMS measurement
- Voltage / Continuity / Capacitance / Diode and Frequency
- Large back lit display
- Non Contact AC voltage detection
- Auto / Manual V (AC / DC) 1000V
- Auto / Manual Ω up to 60 MΩ
- NCV Non Contact AC voltage detection (audible and visual) >100V
-
-
Information on the calibration of newly purchased equipment and what it means to you.
Calibration and its certification comes in varying forms on new equipment and in this section, we will break it down into the three areas that we use to classify calibration state at the point of purchase.
Manufacturers Calibration Certificate
This is a calibration certificate offered by the manufacturer supplied with the tester. This is also known as an end-of-line certificate or manufacturer’s certificate. These certificates vary depending on the manufacturer and product. They will not have your company's name on them and don’t always show proven test results.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
This instrument comes complete with the manufacturer's calibration certificate. Please be aware that these certificates are generic and may also be time-lapsed.
If you would prefer a personalised full traceable calibration certificate applied to the equipment before dispatch, then please select this option from the drop-down menu above, an additional calibration charge will apply.Manufacturers Certificate of Conformity
A manufacturer's certificate of conformity is not a calibration certificate. It is merely a statement that the equipment has been produced to operate within its intended application, it has no traceable certificate or constitutes any defined results for accuracy before leaving the manufacturing process.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
This instrument comes with a ‘manufacturer's certificate of conformity’. It is important to understand that this does NOT constitute a ‘calibration certificate’. A certificate of conformity merely states that the equipment has been designed and produced to meet the requirements of its intended application.
Where calibration of an instrument is possible we will offer this as a separately purchasable item and may be selected from the drop-down box above. You will be sent a full traceable calibration certificate produced in our laboratory and applied with your details as required.Personalised traceable calibration certificate from isswww
This is a calibration certificate created by us at ISS. This certificate is fully traceable to national and international standards. The certificate will show your company's details, tester information, proven test results and the equipment used to carry out the test. Nearly 90% of all calibrations we do are done in-house in one of our many fully equipped laboratories. You can add this service to your order on the product page before you checkout.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
We are on occasion able to offer FREE calibration on certain products at their point of sale (newly purchased equipment only) please look out for the following badge on the product's page to take advantage of this free offer.
-
-
Socket and See Engineer Digital Multimeter
The Socket & See Engineer DMM is a versatile and reliable digital multimeter designed with exceptional functionality in mind. It offers auto/manual voltage selection allowing measurements up to 1000V, covering a wide range of electrical applications. Current measurement capabilities extend to microamps, milliamps, and currents of up to 10A (600A with clamp adaptor), in both AC and DC modes.
Advanced features include AC voltage waveform analysis, resistance measurement up to 60 megohms, and a built-in continuity check for simplified circuit testing.
Safety is prioritised with non-contact voltage detection (NCV) technology, alerting users to AC voltages above 100V without direct contact. Visual and audible indicators provide assurance during electrical inspections, and the non-contact frequency(NCF) detection feature allows measurement of frequencies from 45 to 75 Hz (50 to 500 VAC).
Convenience features enhance usability, such as the freeze/hold reading function for easy data capture and analysis, auto power-off to conserve battery life and a backlit LCD display for clear visibility in various lighting conditions. The multimeter also includes a relative reading (REL) mode for differential analysis and supports temperature measurement from -40°C to 1000°C, with the included K-type thermocouple extending the range to 250°C.
The Engineer DMM is a reliable tool suitable for professional electricians and engineers alike. With its precision, wide range of measurement options, and user-friendly interface, it ensures accurate measurements and enhances productivity in various electrical applications.
Engineer DMM Comes Supplied With:
- Digital Multimeter
- Test leads
- 9v battery
- K type temperature probe (-40°C to 250°C)
- Operating manual
Key Features:
- True RMS
- 6000 Count
- Digit 3 3/4
- Auto / Manual V (AC / DC) 1000V
- µA / mA / 10A (AC / DC) 6000µA / 600mA / 10A
- AC / DC external clamp adaptor 600A, 1 mV = 1A
- Auto / Manual V(AC) with Hz / % selectable
- AC Current with Hz / % selectable
- Auto / Manual Ω up to 60 MΩ
- Continuity (<50Ω Beep)
- Capacitance 10nF – 100mF
- Diode check (3.0V)
- 10 MΩ Input Impedance
- NCV Non Contact AC voltage detection (audible and visual) >100V
- NCF Non Contact Frequency 45 – 75 Hz (50 – 500 VAC)
- Freeze / Hold Reading
- Auto Power Off (5 mins)
- Relative Reading (REL)
- Frequency / Duty Cycle (Hz / %) (9.999Hz – 55.00KHz / 0.1 – 99.9%)
- Temperature measurement -40°C to 1000°C
- K Type thermocouple (-40°C to 250°C)
About Socket & See
Through consistent contact with Electricians, Engineers and Gas Installation engineers, Socket & See products have been around since 1998 and are designed with both professional and newly-qualified tradespeople in mind.
We started with 3 simple Socket Testers and a vision to develop a range of ‘easy-to-use’, innovative products which our customers could use straight from the box!
The initial principles still stand firm today, all our products have to be - simple to operate, of great quality, innovative, time-saving and cost-effective.
| Key Features | True RMS measurement, Voltage / Continuity / Capacitance / Diode and Frequency, Large back lit display, Non Contact AC voltage detection, Auto / Manual V (AC / DC) 1000V, Auto / Manual Ω up to 60 MΩ, NCV Non Contact AC voltage detection (audible and visual) >100V |
|---|---|
| Product Stock Status | Next Day Delivery (subject to availability) |
| Manufacturer | Socket and See |
| Short Description | For technical specification break-down please see the Engineers Multimeter manual in the resources section above. |
Updated January 2024
Please note, our cut-off time is 2:00pm
Orders requiring calibration
Whilst we take the greatest care to get all orders dispatched and delivered to you in the stated time frame, orders received PM and requiring calibration may on occasion miss dispatch that day, according to the complexity of the calibration.Be assured they will ship on the next dispatch this in most cases should not add more than 24 hours to your delivery.
Bank/Public Holidays
Predicted delivery times are based on regular trading days Monday to Friday. Public holidays, bank holidays and weekends are outside the usual scopeof our dispatch and subject to activities/holidays of our carriers and therefore may incur additional days lead time to your order.
*UK Mainland (Revised March 2021)
| Service | Price |
| Standard FREE 2-3 Day Courier Delivery – UK Mainland only - Zones A & B - Order value OVER £75.00 ex VAT | FREE |
| Standard FREE 2-3 Day Courier Delivery – UK Mainland only - Zones A & B - Order value UNDER £75.00 ex VAT | £4.95 |
| Next WORKING Day (excludes Saturdays, Sundays and public holidays) – UK Mainland only - Zones A & B - ANY order value - Order by 2:00pm | £7.75 |
| Saturday ANYTIME Delivery - Order by 2:00pm | £9.95 |
Delivery Surcharges
Because of the high cost of carriage, we regretfully need to apply a surcharge on all deliveries made in the following regions:
- Zones A & B - Mainland delivery rates apply.
- Zone C - Scottish Highlands (Charges are calculated at the checkout).
- Zone D - Outer Hebrides, Orkney Isles, Shetland Isles, Isle of Man, Scilly Isles, and Channel Islands (Charges are calculated at the checkout).
- Zone E - Northern Ireland (Charges are calculated at the checkout).
- Zone F - Republic of Ireland (Charges are calculated at the checkout).
Offshore Services
All offshore deliveries are a 3-4 day service as standard. This includes Channel Islands, Northern & Southern Ireland, Scottish Islands, Isle of Man and the Scilly Isles.
International delivery
International delivery charges are automatically added to your order at the checkout. For any questions regarding international deliveries please contact us at sales@isswww.co.uk
Export
All export inquiries should be directed to the export division before placement of order.
If no shipping option is available to your selected country please call us FREE on 0800 0224 060 to discuss your requirements.
All stated prices are subject to VAT at the current rate where applicable.
E&OA