Fluke FVF-UG FlukeView Forms Software Upgrade
- Software Upgrade
- Advanced Software
- Advanced Software
-
-
Information on the calibration of newly purchased equipment and what it means to you.
Calibration and its certification comes in varying forms on new equipment and in this section, we will break it down into the three areas that we use to classify calibration state at the point of purchase.
Manufacturers Calibration Certificate
This is a calibration certificate offered by the manufacturer supplied with the tester. This is also known as an end-of-line certificate or manufacturer’s certificate. These certificates vary depending on the manufacturer and product. They will not have your company's name on them and don’t always show proven test results.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
This instrument comes complete with the manufacturer's calibration certificate. Please be aware that these certificates are generic and may also be time-lapsed.
If you would prefer a personalised full traceable calibration certificate applied to the equipment before dispatch, then please select this option from the drop-down menu above, an additional calibration charge will apply.Manufacturers Certificate of Conformity
A manufacturer's certificate of conformity is not a calibration certificate. It is merely a statement that the equipment has been produced to operate within its intended application, it has no traceable certificate or constitutes any defined results for accuracy before leaving the manufacturing process.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
This instrument comes with a ‘manufacturer's certificate of conformity’. It is important to understand that this does NOT constitute a ‘calibration certificate’. A certificate of conformity merely states that the equipment has been designed and produced to meet the requirements of its intended application.
Where calibration of an instrument is possible we will offer this as a separately purchasable item and may be selected from the drop-down box above. You will be sent a full traceable calibration certificate produced in our laboratory and applied with your details as required.Personalised traceable calibration certificate from isswww
This is a calibration certificate created by us at ISS. This certificate is fully traceable to national and international standards. The certificate will show your company's details, tester information, proven test results and the equipment used to carry out the test. Nearly 90% of all calibrations we do are done in-house in one of our many fully equipped laboratories. You can add this service to your order on the product page before you checkout.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
We are on occasion able to offer FREE calibration on certain products at their point of sale (newly purchased equipment only) please look out for the following badge on the product's page to take advantage of this free offer.
-
-
FlukeView® Forms Upgrade (UG)
Expand the power of the world's most rugged, accurate handheld test tools with FlukeView® Forms Documenting Software.
To address the increasing demands for reporting and documentation, Fluke presents FlukeView Forms documenting software. FlukeView Forms increases the power of your Fluke tool by enabling you to document, store and analyze individual readings or series of measurements, then convert them into professional-looking documents.
Several versions of the product are available, depending upon the type of cable needed to download data from your instrument and depending upon the data reporting capability you need. FlukeView Forms offers two levels of capability: FlukeView Forms Basic, and FlukeView Forms plus Designer. FlukeView Forms Basic can be used alone to download measurement data and create reports that can be saved and printed. FlukeView Forms plus Designer allows a user to edit an existing form or create a new form to customize the report to individual needs. A common edit might add a company logo and title. See the [Features] tab on this page for more information.
Capability Comparison:
| Capabilities | FlukeView® Forms Basic | FlukeView® Forms plus Designer |
| Transfer data points from your meter to your PC | X | X |
| Number of standard forms | 2 | 9 |
| Able to modify standard forms | No | Yes |
| Includes FlukeView® Forms Designer for customizing forms | No | Yes |
| Number of multiple meters whose data can be viewed simultaneously | 1 | 8 |
| Number of concurrently running instances of FlukeView Forms allowed | 1 | 4 |
| Ability to change company name on report | No | Yes |
| Supports multi-page forms | No | Yes |
FlukeView Forms supports the following test tools:
- Fluke 1550B MegOhmMeter
- Fluke 1653 / 1653B / 1654B / 1652C Electrical Installation Tester
- Fluke 180 series
- Fluke 287 and 289
- Fluke 45
- Fluke 53-II B and 54-II B
- Fluke 568 IR Thermometer
- Fluke 789 ProcessMeter
- Fluke 8808A
- Fluke 8845A/8846A
- Fluke 89-IV and 87-IV
- Fluke 975 AirMeter Test Tool
- Fluke 983 Particle Counter
The ability of FlukeView Forms to support multiple instruments enables the user to install and learn only one software application in order to use these multiple tools fully.
Select the appropriate model number below based upon your requirements:
| Model Number | Description | Cable | Application Level |
| FVF-UG | Software only upgrade, from FVF Basic to FlukeView Forms plus Designer** | No Cable included | FlukeView Forms plus Designer |
| FVF-SC2 | Fluke 280 Series, 53-II B and 54-II B, 789, 1550B, 1653, 180 Series* | USB / IR | |
| FVF-SC4 | Fluke 8808A, 8845A, 8846A, 45* | USB / Serial | |
| FVF-BASIC | Fluke 280 Series, 789, 1550B, 1653, 180 Series* | USB / IR | FlukeView Forms BASIC |
| FVF-SC5 | Software only** | No Cable included |
* Obsolete
** For all instruments listed in table
FlukeView® Forms Basic (FVF-BASIC)
Owners of Fluke 280 series, 180 series, 789 and 1550B, who do not need the full power of FlukeView forms, can use FlukeView® Basic version. Transfer data points from your meter to your PC and use the two standard, non-customizable forms to display your readings in table or graphical form. For a larger array of forms or to use FlukeView® Forms Designer to customize your forms, upgrade to FlukeView® Forms version 3.3 with FVF-UG.
FlukeView® Forms Upgrade (FVF-UG)
You can expand the power of your Fluke Test Tools by upgrading from FlukeView Forms Basic with the FlukeView® Forms Software Upgrade.
With the FlukeView® Forms Software Upgrade you can:
Instantly review and compare data from up to 6 different meters on the same document - providing analysis capabilities that a meter alone can't provide.
Use the array of Upgraded analysis and reporting forms to display your data in tables, graphs or helpful diagrams;even leave notes on the forms to draw attention to a particular event.
Or use the FlukeView® Forms plus Designer to customize your reports or add your company logo.
| Key Features | Software Upgrade, Advanced Software | ||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Product Stock Status | Next Day Delivery (subject to availability) | ||||||||||||||||||||||||||
| Manufacturer | Fluke Testers | ||||||||||||||||||||||||||
| Short Description |
Administrator Privileges required to install software on Windows 2000, XP, or Windows Vista Updated January 2024
Please note, our cut-off time is 2:00pmOrders requiring calibrationWhilst we take the greatest care to get all orders dispatched and delivered to you in the stated time frame, orders received PM and requiring calibration may on occasion miss dispatch that day, according to the complexity of the calibration.Be assured they will ship on the next dispatch this in most cases should not add more than 24 hours to your delivery. Bank/Public HolidaysPredicted delivery times are based on regular trading days Monday to Friday. Public holidays, bank holidays and weekends are outside the usual scopeof our dispatch and subject to activities/holidays of our carriers and therefore may incur additional days lead time to your order. *UK Mainland (Revised March 2021)
Delivery SurchargesBecause of the high cost of carriage, we regretfully need to apply a surcharge on all deliveries made in the following regions:
Offshore ServicesAll offshore deliveries are a 3-4 day service as standard. This includes Channel Islands, Northern & Southern Ireland, Scottish Islands, Isle of Man and the Scilly Isles. International deliveryInternational delivery charges are automatically added to your order at the checkout. For any questions regarding international deliveries please contact us at sales@isswww.co.uk ExportAll export inquiries should be directed to the export division before placement of order. If no shipping option is available to your selected country please call us FREE on 0800 0224 060 to discuss your requirements.
| ||||||||||||||||||||||||||
