Chauvin Arnoux PEL104 Contractor Kit KPEL104MA194HC
- Analyse voltages up to 1000V AC/DC
- Analyse current up to 10000 A
- 8 GB SD memory card supplied
- Self powering via the phase
- Current up to 10 kA AC or 5 kA DC
- Split phase - three phase - with or without neutral
- Real-time PC communication
- Report Generation
- FREE Dataview Software (Full Version)
- User-defined limit alarm and event log with email alerts
-
-
Information on the calibration of newly purchased equipment and what it means to you.
Calibration and its certification comes in varying forms on new equipment and in this section, we will break it down into the three areas that we use to classify calibration state at the point of purchase.
Manufacturers Calibration Certificate
This is a calibration certificate offered by the manufacturer supplied with the tester. This is also known as an end-of-line certificate or manufacturer’s certificate. These certificates vary depending on the manufacturer and product. They will not have your company's name on them and don’t always show proven test results.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
This instrument comes complete with the manufacturer's calibration certificate. Please be aware that these certificates are generic and may also be time-lapsed.
If you would prefer a personalised full traceable calibration certificate applied to the equipment before dispatch, then please select this option from the drop-down menu above, an additional calibration charge will apply.Manufacturers Certificate of Conformity
A manufacturer's certificate of conformity is not a calibration certificate. It is merely a statement that the equipment has been produced to operate within its intended application, it has no traceable certificate or constitutes any defined results for accuracy before leaving the manufacturing process.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
This instrument comes with a ‘manufacturer's certificate of conformity’. It is important to understand that this does NOT constitute a ‘calibration certificate’. A certificate of conformity merely states that the equipment has been designed and produced to meet the requirements of its intended application.
Where calibration of an instrument is possible we will offer this as a separately purchasable item and may be selected from the drop-down box above. You will be sent a full traceable calibration certificate produced in our laboratory and applied with your details as required.Personalised traceable calibration certificate from isswww
This is a calibration certificate created by us at ISS. This certificate is fully traceable to national and international standards. The certificate will show your company's details, tester information, proven test results and the equipment used to carry out the test. Nearly 90% of all calibrations we do are done in-house in one of our many fully equipped laboratories. You can add this service to your order on the product page before you checkout.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
We are on occasion able to offer FREE calibration on certain products at their point of sale (newly purchased equipment only) please look out for the following badge on the product's page to take advantage of this free offer.
-
-
Chauvin Arnoux PEL104 Contractor Kit KPEL104MA194HC
The PEL104 power logger measures and records all the useful data for energy consumption diagnostics. The PEL104 can be used without cutting off the mains power supply.
PEL104 Comes Supplied With:
- 1 x PEL104 Energy Logger
- 3 x MA194/350 CT’s
- 4 x Black Mag Probes
- 1 x Dataview software licence key (software downloadable from Chauvin Arnoux)
- 1 x Hard Backed Case
- 4x Loaded reeling boxes
- 4 x Black safety leads, 3m, banana-banana, straight-straight attached by a Velcro tie.
- 4 x Black crocodile clips
- 1x Type A-B USB cord 1.5m.
- 1 x Mains cord 1.5m
- 1 x PEL adapter (PEL104)
- 1 x Carrying bag.
- 12 x Set of inserts and rings for marking the leads and current sensors according to phase
- 1 x 8 GB SD-card (in the instrument).
- 1 x USB SD-Card adapter
- 1 x Checking attestation.
- 1 x Multilingual safety data sheet.
- 1 x Quick Start Guide.
PEL Series Applications:
- Ideal for all types of electrical cabinets and Low Voltage installations
- Implementation without cutting off the mains power supply
- Recording duration up to several months or years
- Breakdown of energy losses
- Characterization of electric motors
Key Features:
The PEL10x power and energy loggers perform the following measurements:
- RMS and DC measurements with 128 samples/cycle – simultaneously on each phase
- AC and/or DC voltages up to 1,000 V
- Analogue measurements
- Measurements on motors
- Self-powering via the phase
- Current up to 10 kA AC or 5 kA DC (depending on the current sensor).
- The PEL100 models offer a wider measurement range by using voltage and current ratios (up to 650,000 V / 25,000 A)
- Power values from 10 W/var/VA to 10 GW/Gvar/GVA
- Energy values up to 4 EWh / 4 EVAh / 4 Evarh & total energy (4 quadrants)
- Breakdown of energy losses
- Characterization of electric motors
- Phase data: cos φ, tan Φ, power factor (PF)
- Crest factor
- THD calculation for currents and voltages
- Harmonics up to the 50th order for currents and voltages
- DC, 50 Hz, 60 Hz and 400 Hz measurements
- Recording of the measurements and calculation results on the SD card
- Automatic recognition of the type of sensors connected
- Numerous network types supported: split-phase, three-phase with or without neutral, etc.
- Communications: USB, Bluetooth, Ethernet, Wifi, GSM 3G, GPRS
- Software for data transfer, real-time communication with a PC and report generation
Ergonomics
Portable, rugged and compact, its magnetized casing makes it easy to set up, including in an electrical cabinet. The PEL104 is a logger equipped with 3 voltage channels and 3 current channels. No more battery problems, as the logger self-powers directly via the phase by means of the accessory included.
The backlit LCD screen equipped with a triple digital display is particularly easy to read.
The PEL 104 is equipped with an SD card capable of storing several years' data, an ideal function for measurement campaigns.
Measurements
Suitable for all types of electrical networks, the PEL104 automatically recognizes the sensors connected. It measures voltage up 1,000 VAC/VDC and current up to 10 kVAC / 5 kVDC. Its wide measurement ranges enable it to record power values up to 10 GW/Gvar/GVA, and energy up to 4 EWh/EVAh/Evarh.
It is equipped with an Alarm mode. The user can define limits and a list of events is recorded.
Ultra-communicating
The PEL104 is equipped with multiple communication modes: USB, Ethernet, Bluetooth, Wifi and 3G/GPRS.
The new 3G/GPRS mode allows users to insert a SIM card in the PEL for remote connection via a GSM 3G link. Because measurement campaigns often stretch over several days or weeks, it is important to check that the PEL is functioning correctly during this period.
With all these modes, it is possible to monitor the measurements in real-time and recover the measurement data remotely anywhere in the world.
When an alarm is triggered, users can automatically receive an email alert.
Android
In the field, the dedicated ANDROID application can be used to check that the PEL is operating correctly and to modify its configuration. This function enables measurements for applications on motors: rotation speed, torque and engine efficiency. No more need to add specific sensors in order to monitor a motor's behaviour in real-time.
MA194-350 Current Clamps:
The PEL104 Contractors Kit comes as standard with 3x additional current clamps.
IEC 61010 1000V CAT III et 600V CAT IV
Current clamps, MiniFlex® and AmpFlex® flexible current sensors are used to measure the current flowing in a cable without opening the circuit. They also insulate the user from dangerous voltages in the circuit.
MiniFlex® MA194 350 mm
Measurement range * 100 mA - 10 000 A 100 mA - 10 000 A 100 mA - 10 000 A
Clamping diameter 100 mm
Dimensions (L x W x H) approx. 170 x 110 x 18 mm
Cord 3 metres long
Weight approx. 120 g
Dataview Software:
Comes as standard with the PEL104 Contractors Kit.
The PEL Transfer software can be used to analyse the data recorded with the PEL100 models. On the basis of the power measurement campaigns performed, the software automatically decomposes the losses detected.
New: the software directly calculates the cost of the power consumed and gives the result in the local currency selected.
The DATAVIEW software platform can be used to generate reports. Users can set alarm thresholds on the various measurements made in order to obtain a customized measurement report.
The DataView® software is an essential tool for configuring and performing measurements, viewing data in real time, recovering recorded data and creating standard or customized measurement reports.
It provides a single software platform for operating most Chauvin Arnoux products, including:
- QualiStar C.A 8331, C.A 8333, C.A 8336 and C.A 8436 power analysers
- C.A 8220 and C.A 8230 power controllers
- PEL102, PEL103 & PEL105 power and energy loggers
- C.A 6470N, C.A 6471 and C.A 6472 earth testers
- C.A 6543, C.A 6547, C.A 6549, C.A 6550, C.A 6555, C.A 6526, C.A 6532 and C.A 6534 insulation testers
- F407 and F607 multimeter clamps
- All the SIMPLE LOGGER 2 models
- C.A 6417 earth clamps
- C.A 6116N C.A 6117 multi-function installation testers
- DTR8510 ratiometer
- C.A 1821, C.A 1822, C.A 1823 thermometers
- C.A 1246 thermo-hygrometer
- C.A 1227 thermo-anemometer
- C.A 1110 Lightmeter
- CA 10101 pH meter
- CA 10141 conductivity meter
The simple-to-use DataView® software automatically recognizes the instrument connected to the PC and gives the user direct access to the data recorded in the instrument, its configuration and the real-time data.
DATAView® automatically generates measurement reports or creates new customized reports on request.
This tool also offers a large number of additional functions for greater user comfort or for more detailed analysis: a zoom on the graphs to analyse certain parts more closely, display of various recorded parameters on request, export of stored data into Excel, linking and integration of objects (OLE), etc.
DataView can be used to automatically link the address details of customers, work sites, etc., extracted from a database, to the measurement reports.
The instruments are connected to the PC via USB, RS232, WiFi or Bluetooth, depending on the model.
The following minimum configuration is required:
Windows 7/8/10 (32/64 bit)
1GB of RAM for Windows 7/8/10 (32 bit)
2GB of RAM for Windows 7/8/10 (64 bit)
80MB space on hard disk (200MB recommended)
PEL Transfer
(Additional Software)
The PEL Transfer software can be used to control the PEL 102, PEL 103, PEL 104, PEL 105 and PEL 106 power and energy loggers.
The PEL Transfer software is a tool for:
- Configuring the instruments,
- Downloading and viewing the data stored in the memory,
- Performing instantaneous acquisition operations,
- Displaying the data in the form of tables or graphs,
- Exporting the measurement data into (*.dvb files) or into a spreadsheet.
PEL Transfer is available as a free download from Chauvin Arnoux here: pel_v2.06.13629.zip
Compatible with Windows 7, 8, 8.1 and 10
Chauvin Arnoux DataView software is not supplied with the PEL Transfer software
Which PEL Series energy logger is right for you?
Comparison Chart
isswwwand Chauvin Arnoux
The Chauvin Arnoux Group of companies, incorporating the Metrix and Multimetrix brands are synonymous with design and production of the finest quality products for the electrical testing industry, covering a diverse sector of the market for over 100 years. From their awarded Digiflex current sensors, universal testers, multimeters, network and power analysers, right up to laboratory instrumentation and beyond.
ISSWWW and Chauvin Arnoux have enjoyed a close working partnership for many years and we supply many of their products to trade and industry the world over.
| Key Features | Analyse voltages up to 1000V AC/DC, Analyse current up to 10000 A, 8 GB SD memory card supplied, Self powering via the phase, Current up to 10 kA AC or 5 kA DC, Split phase - three phase - with or without neutral, Real-time PC communication, Report Generation, FREE Dataview Software (Full Version), User-defined limit alarm and event log with email alerts | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Product Stock Status | Next Day Delivery (subject to availability) | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Manufacturer | Chauvin Arnoux | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Short Description |
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Updated January 2024
Please note, our cut-off time is 2:00pm
Orders requiring calibration
Whilst we take the greatest care to get all orders dispatched and delivered to you in the stated time frame, orders received PM and requiring calibration may on occasion miss dispatch that day, according to the complexity of the calibration.Be assured they will ship on the next dispatch this in most cases should not add more than 24 hours to your delivery.
Bank/Public Holidays
Predicted delivery times are based on regular trading days Monday to Friday. Public holidays, bank holidays and weekends are outside the usual scopeof our dispatch and subject to activities/holidays of our carriers and therefore may incur additional days lead time to your order.
*UK Mainland (Revised March 2021)
| Service | Price |
| Standard FREE 2-3 Day Courier Delivery – UK Mainland only - Zones A & B - Order value OVER £75.00 ex VAT | FREE |
| Standard FREE 2-3 Day Courier Delivery – UK Mainland only - Zones A & B - Order value UNDER £75.00 ex VAT | £4.95 |
| Next WORKING Day (excludes Saturdays, Sundays and public holidays) – UK Mainland only - Zones A & B - ANY order value - Order by 2:00pm | £7.75 |
| Saturday ANYTIME Delivery - Order by 2:00pm | £9.95 |
Delivery Surcharges
Because of the high cost of carriage, we regretfully need to apply a surcharge on all deliveries made in the following regions:
- Zones A & B - Mainland delivery rates apply.
- Zone C - Scottish Highlands (Charges are calculated at the checkout).
- Zone D - Outer Hebrides, Orkney Isles, Shetland Isles, Isle of Man, Scilly Isles, and Channel Islands (Charges are calculated at the checkout).
- Zone E - Northern Ireland (Charges are calculated at the checkout).
- Zone F - Republic of Ireland (Charges are calculated at the checkout).
Offshore Services
All offshore deliveries are a 3-4 day service as standard. This includes Channel Islands, Northern & Southern Ireland, Scottish Islands, Isle of Man and the Scilly Isles.
International delivery
International delivery charges are automatically added to your order at the checkout. For any questions regarding international deliveries please contact us at sales@isswww.co.uk
Export
All export inquiries should be directed to the export division before placement of order.
If no shipping option is available to your selected country please call us FREE on 0800 0224 060 to discuss your requirements.
All stated prices are subject to VAT at the current rate where applicable.
E&OA