TPI 270 Digital Clamp Meter
- Data Hold
- Voltage AC/DC
- Capacitance Measurement
- Non Contact Voltage Detection
- Continuity Test
- Diode Testing
-
-
Information on the calibration of newly purchased equipment and what it means to you.
Calibration and its certification comes in varying forms on new equipment and in this section, we will break it down into the three areas that we use to classify calibration state at the point of purchase.
Manufacturers Calibration Certificate
This is a calibration certificate offered by the manufacturer supplied with the tester. This is also known as an end-of-line certificate or manufacturer’s certificate. These certificates vary depending on the manufacturer and product. They will not have your company's name on them and don’t always show proven test results.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
This instrument comes complete with the manufacturer's calibration certificate. Please be aware that these certificates are generic and may also be time-lapsed.
If you would prefer a personalised full traceable calibration certificate applied to the equipment before dispatch, then please select this option from the drop-down menu above, an additional calibration charge will apply.Manufacturers Certificate of Conformity
A manufacturer's certificate of conformity is not a calibration certificate. It is merely a statement that the equipment has been produced to operate within its intended application, it has no traceable certificate or constitutes any defined results for accuracy before leaving the manufacturing process.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
This instrument comes with a ‘manufacturer's certificate of conformity’. It is important to understand that this does NOT constitute a ‘calibration certificate’. A certificate of conformity merely states that the equipment has been designed and produced to meet the requirements of its intended application.
Where calibration of an instrument is possible we will offer this as a separately purchasable item and may be selected from the drop-down box above. You will be sent a full traceable calibration certificate produced in our laboratory and applied with your details as required.Personalised traceable calibration certificate from isswww
This is a calibration certificate created by us at ISS. This certificate is fully traceable to national and international standards. The certificate will show your company's details, tester information, proven test results and the equipment used to carry out the test. Nearly 90% of all calibrations we do are done in-house in one of our many fully equipped laboratories. You can add this service to your order on the product page before you checkout.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
We are on occasion able to offer FREE calibration on certain products at their point of sale (newly purchased equipment only) please look out for the following badge on the product's page to take advantage of this free offer.
-
-
TPI 270 Digital Clamp Meter
The TPI 270 400A AC Clamp Meter provides excellent value and offers measurement for AC current up to 400A and AC/DC voltage up to 600V.
Additional measurements include resistance up to 40Ω, frequency up to 400MHz, capacitance up to 40,000µF, and temperature from -34˚C to 537˚C. A DC microamp range (400µA) allows the user to test smoke detectors and it is suitable for a range of other HVAC tasks whilst continuity and diode testing is also available.
Several other advanced measurement features supplement the basic functionality on the TPI 270. It boasts min/max recording and data hold whilst peak hold captures the highest value recorded. Relative mode permits comparison between two values as well as differential temperature. Automatic and manual ranging allow the user to choose between accuracy and precision whilst high resolutions for each parameter help give an in-depth picture of system performance.
The TP 270’s slim design allows it to be worked into tight and awkward spaces whilst all results are shown on a clear digital display that also features an analogue bar graph. Non-contact voltage detection adds additional security alongside the Cat II 1000V and Cat III 600V safety ratings. The meter is supplied with a thermocouple, test leads and a case. A three-year manufacturer’s warranty covers the device and it has an 80-hour battery life.
The TPI 270 Clamp Meter Is Supplied With:
- TPI 270 Digital Clamp Meter
- Standard K-Type Thermocouple Probe
- UL-Listed Silicone Test Lead Set with Alligator Clips
- Soft Carrying Pouch
Key Features:
- Test AC/DC voltage to 600V
- DC current measurements to 400μA
- AC current measurements to 400A
- Resistance measurements to 40MΩ
- Frequency measurements to 400MHz
- Capacitance testing to 40000μF
- Temperature measurements to 1000°F
- Continuity and diode testing
- Small-size jaws to fit in tight applications
- Non-contact voltage detector built-in
- MIN/MAX recording over a time period
- Data hold function temporarily stores the last value taken on the screen
- 4000 count digital display with 41 segment analogue bargraph
- Auto/manual ranging
- Low battery indicator
- Over range indication
- High voltage indicator
- Auto power off after 30 minutes of inactivity
- Separate battery/fuse compartment
Applications:
- Measure flame safety control current
- Test run and start capacitors and motors
- Measure motor run current and capture peak motor start up amperage
- Measure heat anticipator current
- Determine thermocouple voltage
- Test line and control voltages
- Measure heating element resistance
- Measure air temperature in ducts
- Test for the presence of voltage in circuits without contacting the circuit
- Measure temperature differential using relative mode
About TPI Europe
Since 1997, TPI has been striving to offer the latest technology at the most affordable price to technicians, contractors, engineers and others seeking value-based test and measurement instruments. Our mission is to become the leading independent manufacturer and supplier of low cost high-performance industrial instrumentation.
Headquartered in the heart of the “Silicon Forest” in Beaverton, Oregon, TPI combines innovation, performance, customer service and high-value in products which include: Vibration, Combustion, Pressure (manometers), Temperature, Combustible gas, Digital Multimeters, Clamp Meters, IAQ, specialty test and measurement instruments, and a wide range of accessories.
| Key Features | Data Hold, Voltage AC/DC, Capacitance Measurement, Non Contact Voltage Detection, Continuity Test, Diode Testing | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Manufacturer | TPI Test Products International | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Short Description | TPI 270 Digital Clamp Meter
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Product Stock Status | Next Day Delivery (subject to availability) |
Updated January 2024
Please note, our cut-off time is 2:00pm
Orders requiring calibration
Whilst we take the greatest care to get all orders dispatched and delivered to you in the stated time frame, orders received PM and requiring calibration may on occasion miss dispatch that day, according to the complexity of the calibration.Be assured they will ship on the next dispatch this in most cases should not add more than 24 hours to your delivery.
Bank/Public Holidays
Predicted delivery times are based on regular trading days Monday to Friday. Public holidays, bank holidays and weekends are outside the usual scopeof our dispatch and subject to activities/holidays of our carriers and therefore may incur additional days lead time to your order.
*UK Mainland (Revised March 2021)
| Service | Price |
| Standard FREE 2-3 Day Courier Delivery – UK Mainland only - Zones A & B - Order value OVER £75.00 ex VAT | FREE |
| Standard FREE 2-3 Day Courier Delivery – UK Mainland only - Zones A & B - Order value UNDER £75.00 ex VAT | £4.95 |
| Next WORKING Day (excludes Saturdays, Sundays and public holidays) – UK Mainland only - Zones A & B - ANY order value - Order by 2:00pm | £7.75 |
| Saturday ANYTIME Delivery - Order by 2:00pm | £9.95 |
Delivery Surcharges
Because of the high cost of carriage, we regretfully need to apply a surcharge on all deliveries made in the following regions:
- Zones A & B - Mainland delivery rates apply.
- Zone C - Scottish Highlands (Charges are calculated at the checkout).
- Zone D - Outer Hebrides, Orkney Isles, Shetland Isles, Isle of Man, Scilly Isles, and Channel Islands (Charges are calculated at the checkout).
- Zone E - Northern Ireland (Charges are calculated at the checkout).
- Zone F - Republic of Ireland (Charges are calculated at the checkout).
Offshore Services
All offshore deliveries are a 3-4 day service as standard. This includes Channel Islands, Northern & Southern Ireland, Scottish Islands, Isle of Man and the Scilly Isles.
International delivery
International delivery charges are automatically added to your order at the checkout. For any questions regarding international deliveries please contact us at sales@isswww.co.uk
Export
All export inquiries should be directed to the export division before placement of order.
If no shipping option is available to your selected country please call us FREE on 0800 0224 060 to discuss your requirements.
All stated prices are subject to VAT at the current rate where applicable.
E&OA