Beha-Amprobe ALC-110-EUR TRMS Leakage Current Clamp
- 0.001mA Resolution
- 30mm Jaw Size
- Measure up to 60A
- TRMS
- Data Hold
-
-
Information on the calibration of newly purchased equipment and what it means to you.
Calibration and its certification comes in varying forms on new equipment and in this section, we will break it down into the three areas that we use to classify calibration state at the point of purchase.
Manufacturers Calibration Certificate
This is a calibration certificate offered by the manufacturer supplied with the tester. This is also known as an end-of-line certificate or manufacturer’s certificate. These certificates vary depending on the manufacturer and product. They will not have your company's name on them and don’t always show proven test results.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
This instrument comes complete with the manufacturer's calibration certificate. Please be aware that these certificates are generic and may also be time-lapsed.
If you would prefer a personalised full traceable calibration certificate applied to the equipment before dispatch, then please select this option from the drop-down menu above, an additional calibration charge will apply.Manufacturers Certificate of Conformity
A manufacturer's certificate of conformity is not a calibration certificate. It is merely a statement that the equipment has been produced to operate within its intended application, it has no traceable certificate or constitutes any defined results for accuracy before leaving the manufacturing process.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
This instrument comes with a ‘manufacturer's certificate of conformity’. It is important to understand that this does NOT constitute a ‘calibration certificate’. A certificate of conformity merely states that the equipment has been designed and produced to meet the requirements of its intended application.
Where calibration of an instrument is possible we will offer this as a separately purchasable item and may be selected from the drop-down box above. You will be sent a full traceable calibration certificate produced in our laboratory and applied with your details as required.Personalised traceable calibration certificate from isswww
This is a calibration certificate created by us at ISS. This certificate is fully traceable to national and international standards. The certificate will show your company's details, tester information, proven test results and the equipment used to carry out the test. Nearly 90% of all calibrations we do are done in-house in one of our many fully equipped laboratories. You can add this service to your order on the product page before you checkout.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
We are on occasion able to offer FREE calibration on certain products at their point of sale (newly purchased equipment only) please look out for the following badge on the product's page to take advantage of this free offer.
-
-
Beha-Amprobe ALC-110-EUR TRMS Leakage Current Clamp
Designed according IEC/EN61557-13, VDE 0413-13
The ALC-110-EUR true-rms leakage current clamp meter helps users detect, document and compare leakage current readings over time as a means of preventing unplanned downtime, and identifying intermittent RCD/RCCB trips, all without downtime or switching equipment off. The ALC-110-EUR is designed for industrial applications for leakage current testing in installations as well as for appliance testing.
Prevent unplanned downtime by detecting, documenting and comparing leakage current readings over time.
The ALC-110-EUR true-rms leakage current clamp is designed according the relevant standards IEC/EN 61557-13, and helps our customers to keep their business up and running by avoiding unplanned downtime, and identifying intermittent RCD/RCCB trips, all without having to switch equipment off.
The clamp is designed to be able to test leakage current in installations, as well as in appliances.
A special design jaw makes the product very immune to external magnetic fields, which results in much more accurate readings compared to alternative competitive products available in market today.
Applications include the measurement of earth leakage current, differential leakage current, measurement of leakage current through the earth (PE) conductor, tracing the source of earth leakage current, and measurement of current consumption of appliances without interruption to the circuit.
Key Features:
- Following the standard for leakage current clamps IEC/EN 61557-13
- Low influence of external low frequency magnetic fields: ≤ 30 A/m, operating class 2 @ IN: 3.500 mA – 600.0 mA
- True-rms measurements for accuracy when measuring complex, non-sinusoidal waveforms
- Mechanical lock of the jaw; jaw opening 30 mm (1.2 in)
- Highest resolution of 0.001 mA, measure up to 60 A
- Selectable filter function removes unwanted noise
- Selectable filters:
- Low Pass Filter Function for appliance measuring (acc. IEC/EN 61557-16 amendment A)
- 50/60 Hz filter
- no filter - Broad frequency range 15 Hz to 1 kHz which makes this clamp ideal for a wide range of applications including industrial and railway application
- Selectable limits: 0.25 mA, 0.5 mA, 3.5 mA, 10 mA, 12 mA
- Max readings and hold function
- High safety rating: CAT III 600 V
- Auto power-off to save battery life
- Backlight display; auto backlight off and auto power off for extended battery life
| Low frequency magnetic fields | ≤ 30 A/m, operating class 2 @ IN : 3.500 mA to 600.0 mA / 40 Hz to 1 kHz |
| Measurement category | CAT III 600 V |
| True-rms | Yes |
| AC frequency | 15 Hz to 1 kHz |
| Low pass filter | 50 – 60 Hz, for appliance measuring acc. EN61557-16 amendment A, no filter |
| Limit judgement | 0.25 mA, 0.5 mA, 3.5 mA, 10 mA, 12 mA |
| Jaw opening | 1.2 in (30 mm) max. |
| Jaw locking | Yes |
| Backlight function | Yes |
| Overload protection | 60 A |
| Auto power off | Idle 20 minutes |
| Auto ranging | Yes |
| Max hold | Yes |
| Data hold | Yes |
| Complies with IEC/EN 61557-13 | Yes |
| Built according IEC/EN 61010-2-032 | Yes |
Typical Applications:
- Measurement of earth leakage current
- Measurement of differential leakage currents
- Measurement of leakage current through the earth (PE) conductor
- Tracing the source of earth leakage current
- Measurement of current consumption of appliances in service or customer service sector without interruption to the circuit
Safety Certification:
All Beha-Amprobe tools, including the Beha-Amprobe ALC-110-EUR, are rigorously tested for safety, accuracy, reliability, and ruggedness in our state-of-the-art test lab. In addition, Beha-Amprobe products that measure electricity are listed by a 3rd party safety lab, either UL or CSA.
This system assures that Beha-Amprobe products meet or exceed safety regulations and will perform in a tough, professional environment for many years to come.
ISSWWW and Beha-Amprobe - A Fluke Company
With a combined experience of over 100 years, well-known German brand Beha and US-based Amprobe have a track record to be proud of. Now we have joined forces, and together we are committed to making your job safer, faster and easier than ever. Our expertise is legendary. Almost 70 years ago in 1948, we invented the very first clamp meter, and we haven’t stopped innovating since.
The Amprobe brand has always remained a staple among our stockholding. It's pedigree and price point make the brand a quality offering that rival higher priced brands for comparable technology. You can trust Amprobe, thousands do.From multimeters to voltage detectors, at Beha-Amprobe we constantly improve our designs to provide you with the very best quality tools and support.
| Key Features | 0.001mA Resolution, 30mm Jaw Size, Measure up to 60A, TRMS, Data Hold | ||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Manufacturer | Amprobe | ||||||||||||||||||||||||||||||||||||
| Short Description |
|
||||||||||||||||||||||||||||||||||||
| Product Stock Status | Next Day Delivery (subject to availability) | ||||||||||||||||||||||||||||||||||||
Updated January 2024
Please note, our cut-off time is 2:00pm
Orders requiring calibration
Whilst we take the greatest care to get all orders dispatched and delivered to you in the stated time frame, orders received PM and requiring calibration may on occasion miss dispatch that day, according to the complexity of the calibration.Be assured they will ship on the next dispatch this in most cases should not add more than 24 hours to your delivery.
Bank/Public Holidays
Predicted delivery times are based on regular trading days Monday to Friday. Public holidays, bank holidays and weekends are outside the usual scopeof our dispatch and subject to activities/holidays of our carriers and therefore may incur additional days lead time to your order.
*UK Mainland (Revised March 2021)
| Service | Price |
| Standard FREE 2-3 Day Courier Delivery – UK Mainland only - Zones A & B - Order value OVER £75.00 ex VAT | FREE |
| Standard FREE 2-3 Day Courier Delivery – UK Mainland only - Zones A & B - Order value UNDER £75.00 ex VAT | £4.95 |
| Next WORKING Day (excludes Saturdays, Sundays and public holidays) – UK Mainland only - Zones A & B - ANY order value - Order by 2:00pm | £7.75 |
| Saturday ANYTIME Delivery - Order by 2:00pm | £9.95 |
Delivery Surcharges
Because of the high cost of carriage, we regretfully need to apply a surcharge on all deliveries made in the following regions:
- Zones A & B - Mainland delivery rates apply.
- Zone C - Scottish Highlands (Charges are calculated at the checkout).
- Zone D - Outer Hebrides, Orkney Isles, Shetland Isles, Isle of Man, Scilly Isles, and Channel Islands (Charges are calculated at the checkout).
- Zone E - Northern Ireland (Charges are calculated at the checkout).
- Zone F - Republic of Ireland (Charges are calculated at the checkout).
Offshore Services
All offshore deliveries are a 3-4 day service as standard. This includes Channel Islands, Northern & Southern Ireland, Scottish Islands, Isle of Man and the Scilly Isles.
International delivery
International delivery charges are automatically added to your order at the checkout. For any questions regarding international deliveries please contact us at sales@isswww.co.uk
Export
All export inquiries should be directed to the export division before placement of order.
If no shipping option is available to your selected country please call us FREE on 0800 0224 060 to discuss your requirements.
All stated prices are subject to VAT at the current rate where applicable.
E&OA