Drummond SMKIT10 Smart Meter Installation Kit

The comprehensive kit includes a Buzz-It check plug for checking the wiring on 13A sockets, a non-contact voltage indicator with probe tip for identifying phase and neutral lines and a single pole contact voltage tester suitable for use when wearing protective gloves and gauntlets. For CAT IV supply side safe isolation testing there is a Drummond test lamp with proving device. A soft carry case is included for the whole kit.

A Closer Look at the Contents:

• 1 x BZ101 – Buzz-It Check Plug with Sounder for UK 13A Sockets 
• 1 x TEK101 – Non-contact voltage indicator with built in proving device 
• 1 x VT7 – Single Pole Contact Voltage Tester suitable for use when wearing PPE 
• 1 x MTL10 – Drummond AC/DC Test Lamp 600V CAT IV 
• 1 x PD440 – Proving Device 
• 1 x TC70 – Combination soft carry case

Martindale BZ101 (Buzz-It) Socket Tester

The BZ101 provides a fast and simple solution for checking that 13A sockets are wired correctly. It uses the same LED indication as the CP501 but has the added benefit of an audible sounder to confirm that the wiring is correct.

This is particularly useful when checking sockets that are not easily visible or in difficult to access locations.

With the audible indication, the Buzz-It can also be used as a basic fuse finder, when the correct fuse is pulled the buzzer stops.

Detects 28 fault conditions

Martindale TEK101 Non Contact Voltage Detector

The Martindale TEK101 is a simple to use non-contact voltage indicator with both audible and visual warnings and an extended probe tip for access to confined spaces. Optimised for identifying energised conductors at voltages within the range 180V to 600V AC, it incorporates a unique built-in 50Hz proving unit which tests the sensor operation, battery and LED.

The TEK100 Series of voltage indicators are the only non-contact voltage detectors with a built-in proving device that really proves the entire circuit is fully functional avoiding the need for a separate proving unit.

The tip design and optimised sensitivity make it possible to discriminate between adjacent live conductors where standard voltage indicators struggle. The high resolution capability of the TEK101 improves safety and saves time on-site. The pocket sized design conforms to CAT IV 1000V safety regulations.

Martindale VT7 Single pole Voltage Indicator

A single pole contact voltage indicator which detects AC voltages of 50V-600V with bright LED indication.

This ergonomically designed voltage tester has a self-test function and is IP54 rated, for indoor and outdoor use. The tester is of durable construction making it suitable for both industrial and domestic applications.

This unit can be used when wearing protective gloves and gauntlets. Potentially unsafe direct contact with a finger is not required.

The probe is GS38 compliant.

Drummond MTL10 Test Lamp

The John Drummond MTL10 gives safe indication of voltage between 50V and 500V AC and 50V to 750V DC.

The robust design meets the recommendations of the Health and Safety Executive in their guidance notes on the electrician’s test lamp (GS38) as well as complying with BS EN61243-3 and BS EN61010, CATIII 1000V and CAT IV 600V.

Both the lamp housing and the probe have a finger shield and insulated probe tip with only 4mm of exposed metal. A two layer double insulated cable with white inner insulation gives a clear warning of abrasion that might compromise the user’s safety, and is resistant against heat and oil. To enable use in most circumstances, a right angled probe tip is supplied in addition to the two straight tips.

For maximum ease of use, the right angled probes can be rotated through 90, 180 and 270 degrees. Four distinct bands of illumination, with a 360° viewing angle, provide indication of voltages above 50, 120, 230 and 400 volts even in bright sunlight. This allows accurate identification of potentially lethal voltages above 50V and enables the user to distinguish between 110V, 230V and phase to phase voltages in a 3 phase system.

Martindale PD440 440V AC Proving Unit

The Martindale PD440 is a 440V AC proving device, designed to enable voltage indicators to be fully checked, in compliance with Health & Safety recommendations. Using a voltage indicator without first proving it is working correctly could prove fatal.

The PD440 is compatible with the new Martindale VI13800 & the Martindale VI13700.

It can also be used to check Drummond and other filament test lamps as well as standard multimeters and other manufacturers two pole voltage indicators.

There is now a facility to power the PD440 proving devices with the addition of a 12V DC power connection point. The units can be powered by either alkaline batteries or a 12V power supply. There are two power supply units available for the proving devices, the PSUPD230 and the PSUHPAT12. The PSUPD230 can be connected to mains power and the PSUHPAT12 is a 12v power supply suitable for use in a car/van cigarette lighter.

Martindale TC70 VTPD Soft Carry Case

A Soft carry case for the Martindale VT25 and VT28 voltage testers and the PD690 proving device. The front pocket for the storing the proving device has a clear front with two small apertures allowing the unit to be accessed without removing it from the case.

Dimensions 320mm x 100mm x 100mm.