Megger MFT1741+ plus EVCA210-UK EV TEST KIT 1
|
Megger MFT1741+ Multifunction Tester Technical Specifications |
||
| Insulation Test | ||
| Output voltage | -0% +20% at rated load or less | |
| Voltage display | ±3% ±3 digits ±0.5% of rated voltage | |
| Short circuit current | 1.5 mA nominal test current | |
| Test current on load | 1 mA at min pass values of insulation | |
| Insulation Accuracy | ||
| 1000 Volts | 10 kΩ ~ 999 MΩ | ±3% ±2 digits |
| 500 Volts | 10 kΩ ~ 500 MΩ | ±3% ±2 digits |
| >500 MΩ | ±10% ±4 digits | |
| 250 Volts | 10 kΩ ~ 250 MΩ | ±3% ±2 digits |
| >250 MΩ | ±10% ±4 digits | |
| 100 Volts | 10 kΩ ~ 100 MΩ | ±3% ±2 digits |
| >100 MΩ | ±10% ±4 digits | |
| Resistance and Continuity | ||
| 0.01 Ω ~ 99.9 Ω | ±2% ±2 digits | |
| 100 Ω ~ 99.9 kΩ | ±5% ±2 digits | |
| Open circuit voltage | 5 V ±1 V | |
| Test current (user selectable) | (0 Ω ~ 2 Ω) | |
| 205 mA ±5 mA | ||
| 15 mA ±5 mA (user selectable) | ||
| Loop Test | ||
| Live to earth/neutral supply | 48 V ~ 280 V (45 Hz ~ 65 Hz) | |
| Live to live supply | 48 V ~ 500 V (45 Hz ~ 65 Hz) | |
| L-N/L-L tests | ±5% ±5 digits | |
| L-E tests | 0.1 Ω ~ 39.9 Ω | ±5% ±5 digits ± noise margin |
| 40.0 Ω ~ 1000 Ω | ±10% ±5 digits | |
| Display range | 0.01 Ω ~ 1000 Ω | |
| Live to earth PFC range | 20 kA | |
| Live to live PSCC range | 20 kA | |
| Notes |
† Reference conditions apply For test environments see service data |
|
| RCD Tests | ||
| Supply up to 100 mA | 48 V ~ 480 V (45 Hz ~ 65 Hz) | |
| Supply up to 1 A | 48 V ~ 280 V | |
| RCD type | Type AC, A, S | |
| Type B (pure dc) | ||
| No trip test | (1/2xI) | –10% ~ –0% |
| Trip test | (1xI, 2xI and 5xI)+0% ~ +10% | |
| EV | 30 mA ac, 6 mA dc (Mode 1 + 2) | |
| (Mode 1 + 2) Ramp Test | ||
| Touch voltage (0 ~ 253 V) | +5% +15% ±0.5 V | |
| Trip time | ±1% ±1 ms | |
| Trip current | ±5% | |
| Step Increments | ||
| VAR (variable RCD selection) | 10 mA ~ 50 mA | 1 mA steps |
| 50 mA ~ 500 mA | 5 mA steps | |
| 500 mA ~ 1000 mA | 10 mA steps | |
| Supply Measurement | ||
| Voltage | 10 V ~ 600 V | |
| (15 ~ 400 Hz) True RMS | ||
| ±3% ± 1 V ±2 digits | ||
| Phase rotation indication | L1–L2–L3 and L1–L3–L2 | |
| Frequency | 15 Hz ~ 99 Hz ±0.5% ±1 digit | |
| 100 Hz ~ 400 Hz ±2.0% ±2 digits | ||
| Frequency resolution | 0.1 Hz | |
| Power Supply | ||
| Batteries | IEC LR6 type AA alkaline (6 cells - supplied) or 1.2 V NiMH (rechargeable pack of 6 – supplied) | |
| Mains charger for on-board re-charging (4 hours typical) 12 V car charger (cigar lighter lead - optional) | ||
| Earth/ Ground Test | ||
| Resolution | 0.01 Ω | |
| Current | 0.45 mA or 4.5 mA | |
| Noise rejection | 20 V pk/pk (7 V rms) | |
| Max probe resistances | Rp and Rc | |
| 100 kΩ @ 50 V | ||
| 5 kΩ @ 25 V | ||
| 2 and 3 pole method | (0.01 Ω ~ 1.999 kΩ) | |
| ±2.0% ±5 digits | ||
| ART method (1.00 Ω ~ 1.999 kΩ) | ||
| ±5.0% ±5 digits* | ||
| Stakeless method | (1.00 Ω ~ 199 Ω) | |
| ±7.0% ±5 digits* | ||
| Current | ||
| (via optional clamp meter) | ±5.0% ±3 digits. | |
| Range | 0.1 mA to 200 A ac | |
| Resolution | 0.1 mA | |
| mV Sensor Input | ||
| Including temperature (third party module) | ±1.0% ±2 digits | |
| Range | 0.0 mV to ±199.9 mV dc | |
| Resolution | 0.1 mV | |
| Data storage | ||
| Capacity | 1000 results | |
| Bluetooth® communication | ||
| Safety | IEC 61010-1:2010 | |
| IEC 61010-30:2010 | ||
| IEC 61010-031:2008 | ||
| 600 V CAT III / 300 V CAT IV | ||
| (Max Phase to Phase 600 V) | ||
| IEC 61557:2007 parts 1 to 10 | ||
| EMC | IEC61326 edition 2 location class B | |
| Operating temperature range and humidity | -10 °C ~ +55 °C | |
| 90% R.H. at +40 °C max | ||
| Storage temperature range and humidity | -25 °C ~ +70 °C | |
| Maximum altitude | 2000 m | |
| Weight (instrument and case) | 1 kg (with batteries, excluding case) | |
| Dimensions (instrument and case) | 220 mm H x 390 mm W x 285 mm D | |
| IP rating | IP54 | |
| Calibration temperature | +20 °C | |
| Temperature coefficient | <0,1% per °C For test environments see service data. | |
| Megger EVCA210 Charge point Adapter Technical Specification | |
| Input Voltage | Up to 250 V (single phase system) / up to 430 V (three phase system) |
| Input Frequency | 50/60 Hz |
| PE Pre-Test | Yes - Push button |
| CP Error “E” Simulation | Push button |
| PP Simulation | NC, 13 A, 20 A, 32 A, 63 A |
| CP States | A, B, C, D |
| CP Error “E” | Yes |
| PE Error (Earth Fault) | Yes |
| Measuring Ports L1, L2, L3, N and PE | Max. 250/430 V, CAT II 300 V, max. 10 A |
| Mains Socket | Max. 250 V, CAT II 300 V max. 10 A, |
| Note: Do not load mains socket simultaneously with measuring ports! |
|
| CP Signal Test Ports | Approx. +/-12 V, CAT 0 (under normal condition) |
| In case of wrong wiring or error of the charging station these terminals |
|
| Measurement Category | CAT II 300 V |
| Altitude Above Ssea Level. | 2000 m max |
| Weight | Approx: 780g |
| IP-Rating | IP54 |
| CE Directive | Low Voltage Directive LVD 2014/35/EU |
| Safety | IEC/EN 61010-1:2010 |
| IEC/EN 61010-2-030:2010 | |
| Working Temperature Range | 0 ... +40 °C |
| Storage Temperature Range | -10 ... +50 °C |
| Reference Humidity Range | 10 ... 60% relative humidity w/o condensation |
| Working Humidity Range | 10 ... 85% relative humidity w/o condensation |
Description
This instrument comes complete with your choice of free gift from the drop-down menu above.
Choose from a calibration voucher for next year, a 50m R2 wander lead or a set of quality silicone test leads.
How about any one of the IET Guidance Notes, or a quality two-pole tester?
Whatever you choose you can be sure you're getting a fantastic deal at Instrument Sales & Services
Megger MFT1741+ Multifunction Tester and EVCA210-UK Adapter
The Megger EV Test Kit 1 gives you Megger's flagship MFT1741+ Multifunction tester and the EVCA210-UK charge point adapter.
*If you are looking to purchase the EVCA210-UK adapter separately, please see our listing here.
Particularly effective in areas that suffer from high electrical noise, the Megger MFT1741+ provides all the tests needed to complete the necessary electrical certifications for industrial, commercial and domestic fixed wiring installations.
Save time and get non-trip loop testing down to 8 seconds with the MFT1741+’s new Loop Impedance testing technology! This innovative ability also increases the accuracy of results as it prevents the RCD from influencing the total loop impedance value. What’s more, you can measure the degree of confidence in the accuracy of the measured loop impedance, thanks to Megger’s new Confidence Meter measurement analysis (patent pending). This technology uses the digital ARC to indicate the analytical process, then continually monitors and adjusts the measurement when circuit noise is present, resulting in a dramatically improved and repeatable test result.
You can even test electric vehicle charge points with the MFT1741+! It comes with an automatic EV Charge Point RCD test sequence, including the 6 mA DC test*.
Easy-to-use and quick to learn, this instrument has no hidden menus or complicated screens but instead has colour-coded function controls that make range selection simple and speedy. Additionally, it can be operated ambidextrously with dual TEST and LOCK buttons at both sides.
The MFT1741+ is designed for tough environments, with IP54 protection against dust and water and an EN61010 CATIV safety rating. Indeed, the MFT can withstand accidental misuse and voltage transients, keeping you safe on the job.
Megger MFT1741+ Comes Supplied With:
- Printed quick start guide
- Full user guide on CD
- Calibration certificate
- Switched probe SP5
- Neck strap - Megger embroidered
- 3 Wire lead set with prods and clips
- Mains plug test lead (BS1363)
- AC battery charger
- Large soft pouch with extra storage
*Important Calibration Information:
This instrument comes complete with the manufacturer's calibration certificate. Please be aware that these certificates are generic and may also be time lapsed.
If you would prefer a personalised full traceable calibration certificate applied to the equipment before dispatch, then please select this option from the drop-down menu above, an additional calibration charge will apply.
General Features:
Quick to pick up and use, the function controls are colour coded to make range selection easy and fast. They also reduce the chance of using the wrong function or range. The large crystal clear backlit display uses the Megger digital/analogue arc, providing indication of fluctuating readings while the dual digital readout shows precise values of key measurements simultaneously with the test parameters, such as the output voltage on insulation testing as well as the resistance value in MΩ.
Visible and audible safety warnings are paramount when testing high energy systems and the MFT1741+ includes full input protection and safety warnings when a hazardous voltage is present. If live voltages exist on a circuit during insulation or continuity testing, the voltage is displayed on the screen. If this voltage exceeds a safe level, further testing is inhibited and a warning beep sounds. The MFT1741+ features internally rechargeable batteries and charger with a charge time of less than 4 hrs, so reducing the cost of ownership. The new MFT1741+ has been designed for tough environments and ultimate reliability.
Features include a rubber over mould for extra protection and grip, IP54 protection against dust and water and an EN61010 CAT IV safety rating. Its class leading input protection ensures the MFT can withstand accidental misuse and voltage transients when other testers can’t. All this in an intuitive and easy to use instrument with no hidden menus or complicated screens. Included with the instrument: standard 3-wire lead-set and a mains test lead, a switched probe for fast and easy testing, a full 12-month calibration certificate and warranty upgradeable to 3 years warranty, free of charge. The MFT1741+ is supplied in a large soft pouch with plenty of additional space for optional extras like a few tools and the earth electrode test kit, comprising 2 spikes and 3 long test leads
Applications:
The MFT1741+ offers a wide range of test functions, designed for all electrical installation testing and verification of low voltage building wiring and distribution testing scenarios. The MFT1741+ is IEC 61010 CAT IV 300 V rated for safe connection anywhere within the LV network on single and 3 phase systems. The unique modern styling allows it to be operated while stood on the floor, whilst up a ladder or platform, and optimised for hanging around the user’s neck. Dual TEST and LOCK buttons - one pair at each end - makes the testers easy to operate left or right handed.
New electric vehicle charge point testing
The MFT1741+ includes an automatic EV Charge Point RCD test sequence, including the 6 mA dc test*.
Test results can be reviewed or saved to memory and reviewed later.
This kit comes complete with the EVCA210-UK adapter giving you full EV point testing right out of the box.
Key Features:
- Testing of Electric Vehicle Charge Points*
- Enhanced non-trip loop impedance measurement technology
- “Confidence meter” measurement analysis (patent pending)
- Full single and 3 phase compliant installation testing
- 10 mA to 1 A single and 3 phase RCD testing
- Earth testing and stake-less testing for electrode resistance measurement*
- Simple colour-coded test selection
- Ambidextrous operation
- Internal memory and Bluetooth® communications
- EN61010 CAT IV safety rating and tough IP54 case
The MFT1741+ multifunction tester is an instrument designed for testing low voltage electrical installations and especially in locations that suffer from high electrical noise. It provides all the tests required to complete the necessary electrical certification for industrial, commercial and domestic fixed wiring installations, and includes:
- TRMS System voltage and frequency measurement
- Insulation test at 100 V, 250 V, 500 V and 1000 V Including input protection against live circuits up to 600 V even when insulation test is locked-on
- Continuity resistance at 200 mA or 15 mA
- Automatic start - no need to press TEST so leaving both hands free to hold probes
- Resistance range up to 100 kΩ with fast continuity buzzer at selectable thresholds
- Earth loop impedance testing, with:
New 3 wire non-trip technology
New confidence meter measurement
2 and 3 wire non-trip range
2 wire Hi current including phase to phase
Prospective fault current measurement up to 20 kA - RCD testing including:
Type ac, A, S, B and programmable RCDs
Testing of Electric Vehicle Charge Points RCD’s*
3-phase RCDs
Auto-test routine
EV Charge Point RCD Testing - Earth spike testing
2-pole/3-pole*, ART* and Stake-less* techniques
* With appropriate optional accessories
New Loop Impedance testing technology:
The MFT1741+ includes a new non-trip loop testing technology that:
- Prevents any influence the RCD may present to the total loop impedance value.
- Faster non-trip loop testing down to 8 seconds.
This technique also allows testing of loop impedance through 10mA type ac and Type A RCDs.
New “Confidence meter*” measurement analysis (Patent pending)
Overlaying the new non-trip loop impedance measurement is the new Megger “Confidence meter”. As loop impedance values can be dramatically affected by circuit noise, the Confidence Meter displays the degree of confidence in the accuracy of the measured loop impedance. Using the digital ARC to indicate the analytical process, the measurement is continually monitored and adjusted when circuit noise is present, resulting in a dramatically improved and repeatable test result.
Spares & Accessories (Not Supplied):
- Fused 10 A test lead set (red/blue/green) with prods and clips 1001-975
- XTL30 Extension Test Lead 30 m 2007-998
- XTL50 Extension Test Lead 50 m 2207-997
- Cigar lighter adapter for battery charging 6280-332
- Switched Probe SP5 (silicone) 1001-687
- MCC1010 Current measuring clamp 1010-516
- MVC1010 Voltage inducing clamp, calibration 1010-518
check pcb (for stakeless test) and lead - Electrode kit 1001-810
- Test and carry pouch 1006-408
- 3 Pole Earth Test Kit 6210-160
- ETK30 (3 Pole Earth Test Kit) 1010-176
Megger EVCA210 Electric Vehicle Charge point Adaptor
The Megger EVCA210 is a compact, simple to use adapter designed to perform all the functions required by the electrical contractor to fully test Mode 3 AC Electric Vehicle Charge-points.
EVCA210-UK Comes Supplied With:
- Type 1 Charging Plug
- Type 2 Charging Plug
- EVCA210 Carry Case
- Instruction Manual
Key Features:
- Push Button for PE Pre-Test
- Push button for CP Error “E” simulation
- Push button for PE Error (Earth Fault) simulation
- Rotary switch providing PP State simulation
- Rotary Switch providing CP State simulation
- Type 2 Charging Plug for charging points with panel mounted socket outlet or fixed cable with vehicle connector
- Type 1 Charging Plug for charging points with fixed cable and vehicle connector
- (Example Mitsubishi PHEV) – option for the EVCA210/standard on the EVCA210-UK
- IP54 Rating„Carrying Case
- CAT II 300V Rating
- Comply with Low Voltage Directive LVD 2014/35
| EVCA210 | EVCA210-UK | |
| Input voltage 250 V (single phase system) / 430 V (three phase system) | Y | Y |
| Rotary switch providing PP State simulation | Y | Y |
| Rotary Switch providing CP State simulation | Y | Y |
| Push button for CP Error “E” simulation | Y | Y |
| Push button for PE Error (Earth Fault) simulation | Y | Y |
| Measurements on live conductors (L1, L2, L3 and N) and on PE conductor | Y | Y |
| Mains Socket: EVCA210-UK - 13A UK socket EVCA210 - Schuko socket (CEE 7/3) | Y | Y |
| CP signal test, two 4 mm ports for connection to an oscilloscope | Y | Y |
| CAT II 300 V | Y | Y |
| IP Rating IP54 | Y | Y |
| Type 2 Plug for charging points with panel mount-ed socket outlet or fixed cable with vehicle connector. | Y | Y |
| Type 1 Plug for charging points with fixed cable and vehicle connector – Supplied with EVCA210-UK as standard *EVCA-210 (non UK Version) comes with only a type 2 charging plug. |
Y | |
| Soft Carry Case | Y | Y |
Optional accessories for EVCA210 & EVCA210-UK (Included):
- Soft Carry Case 1013-318
- Type 1 Charging Plug 1013-319
- Type 2 Charging Plug 1013-320
isswww and Megger
The extensive Megger product portfolio provides electrical test equipment for an exceptionally wide range of applications at any point of the electricity network. From small handheld low voltage equipment such as multifunction installation testers through to high voltage asset test equipment like insulation resistance testers, circuit breaker analysers, protection relay test systems to transformer condition measurement devices.
Megger designs and manufactures portable electrical test equipment in factories located in Germany, Sweden, the UK, and USA. Megger products help you install, improve efficiency, reduce cost and extend the life of you or your customers’ electrical assets.
Established in the late 1800s, the company has been designing and making test and measurement instruments that perform electrical measurements for preventative maintenance, troubleshooting and commissioning for decades. Megger products have supported customers all over the world to improve their facilities’ efficiency, reduce costs, extend the life of apparatus and through trending and analysis, anticipate equipment failure and future performance.
Being a brand synonymous with the industry and a cornerstone pioneer of many of today’s everyday items of test equipment, ISSWWW are proud to bring you Megger’s full range of equipment and services, now and into the future.
Features & Specification
| Key Features | 10 mA to 1 A single and 3 phase RCD testing, Earth testing and stake-less testing, EN61010 CAT IV safety rating and tough IP54 case, Enhanced non-trip loop impedance measurement, Fully 18th Edition Compliant, Internal memory and Bluetooth® communications, Simple colour-coded test selection, Vehicle Charge Point Testing, Manufacturer Certificate Included | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Product Stock Status | Next Day Delivery (subject to availability) | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Manufacturer | Megger | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Short Description |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Delivery
Updated January 2024
Please note, our cut-off time is 2:00pm
Orders requiring calibration
Whilst we take the greatest care to get all orders dispatched and delivered to you in the stated time frame, orders received PM and requiring calibration may on occasion miss dispatch that day, according to the complexity of the calibration.Be assured they will ship on the next dispatch this in most cases should not add more than 24 hours to your delivery.
Bank/Public Holidays
Predicted delivery times are based on regular trading days Monday to Friday. Public holidays, bank holidays and weekends are outside the usual scopeof our dispatch and subject to activities/holidays of our carriers and therefore may incur additional days lead time to your order.
*UK Mainland (Revised March 2021)
| Service | Price |
| Standard FREE 2-3 Day Courier Delivery – UK Mainland only - Zones A & B - Order value OVER £75.00 ex VAT | FREE |
| Standard FREE 2-3 Day Courier Delivery – UK Mainland only - Zones A & B - Order value UNDER £75.00 ex VAT | £4.95 |
| Next WORKING Day (excludes Saturdays, Sundays and public holidays) – UK Mainland only - Zones A & B - ANY order value - Order by 2:00pm | £7.75 |
| Saturday ANYTIME Delivery - Order by 2:00pm | £9.95 |
Delivery Surcharges
Because of the high cost of carriage, we regretfully need to apply a surcharge on all deliveries made in the following regions:
- Zones A & B - Mainland delivery rates apply.
- Zone C - Scottish Highlands (Charges are calculated at the checkout).
- Zone D - Outer Hebrides, Orkney Isles, Shetland Isles, Isle of Man, Scilly Isles, and Channel Islands (Charges are calculated at the checkout).
- Zone E - Northern Ireland (Charges are calculated at the checkout).
- Zone F - Republic of Ireland (Charges are calculated at the checkout).
Offshore Services
All offshore deliveries are a 3-4 day service as standard. This includes Channel Islands, Northern & Southern Ireland, Scottish Islands, Isle of Man and the Scilly Isles.
International delivery
International delivery charges are automatically added to your order at the checkout. For any questions regarding international deliveries please contact us at sales@isswww.co.uk
Export
All export inquiries should be directed to the export division before placement of order.
If no shipping option is available to your selected country please call us FREE on 0800 0224 060 to discuss your requirements.
All stated prices are subject to VAT at the current rate where applicable.
E&OA