TPI 275 Digital Clamp Meter
-
-
Information on the calibration of newly purchased equipment and what it means to you.
Calibration and its certification comes in varying forms on new equipment and in this section, we will break it down into the three areas that we use to classify calibration state at the point of purchase.
Manufacturers Calibration Certificate
This is a calibration certificate offered by the manufacturer supplied with the tester. This is also known as an end-of-line certificate or manufacturer’s certificate. These certificates vary depending on the manufacturer and product. They will not have your company's name on them and don’t always show proven test results.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
This instrument comes complete with the manufacturer's calibration certificate. Please be aware that these certificates are generic and may also be time-lapsed.
If you would prefer a personalised full traceable calibration certificate applied to the equipment before dispatch, then please select this option from the drop-down menu above, an additional calibration charge will apply.Manufacturers Certificate of Conformity
A manufacturer's certificate of conformity is not a calibration certificate. It is merely a statement that the equipment has been produced to operate within its intended application, it has no traceable certificate or constitutes any defined results for accuracy before leaving the manufacturing process.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
This instrument comes with a ‘manufacturer's certificate of conformity’. It is important to understand that this does NOT constitute a ‘calibration certificate’. A certificate of conformity merely states that the equipment has been designed and produced to meet the requirements of its intended application.
Where calibration of an instrument is possible we will offer this as a separately purchasable item and may be selected from the drop-down box above. You will be sent a full traceable calibration certificate produced in our laboratory and applied with your details as required.Personalised traceable calibration certificate from isswww
This is a calibration certificate created by us at ISS. This certificate is fully traceable to national and international standards. The certificate will show your company's details, tester information, proven test results and the equipment used to carry out the test. Nearly 90% of all calibrations we do are done in-house in one of our many fully equipped laboratories. You can add this service to your order on the product page before you checkout.
Where applicable we will include the following statement relating to the item/s on the products page under the heading *Important Calibration Information.
We are on occasion able to offer FREE calibration on certain products at their point of sale (newly purchased equipment only) please look out for the following badge on the product's page to take advantage of this free offer.
-
-
TPI 275 TRMS Digital Clamp Meter
The TPI 275 TRMS Clamp Meter is a handy meter that can measure current up to 400A AC/DC, voltage up to 600V AC/DC, frequency up to 110MHz and capacitance up to 110mF and resistance up to 110MΩ. This is in addition to temperature measurement up to 537˚C and testing for diode and continuity. High-resolution readings for every parameter provide excellent precision and the meter is also highly accurate thanks to True RMS correction.
The TPI 275 is a particularly useful instrument for HVAC professionals because a micro-amp range allows testing of devices such as smoke detectors whilst the temperature measurement allows the user to check the temperature in air ducts, for example. More advanced measurement features include min/max recording, peak hold, data hold, relative mode and automatic and manual ranging.
In addition to impressive measurement functions, the TPI 275 also features non-contact voltage detection which sounds when a hazardous voltage is detected. This adds an additional layer of safety alongside the safety categorisations of Cat II 1000V and Cat III 600V.
Readings are displayed on a backlit LCD display and the TPI 275 has a simple dial and push-button interface. The slim design and clamp allow the meter to be worked into tight spaces and it is provided a GK11M thermocouple probe, test leads, crocodile clips and a soft carry case. The instrument has a battery life of roughly 80 hours and is covered by a three-year warranty.
The TPI 275 Is Supplied With:
- TPI 275 True RMS Digital Clamp Meter
- Standard K-Type Thermocouple Probe
- Silicone Test Lead Set with Alligator Clips
- Soft Carrying Pouch
Key Features:
- True RMS - high accuracy even on irregular waveforms
- 11000 count digital display
- Measure AC/DC current up to 400A
- Auto/manual ranging
- Data hold function temporarily stores the last value taken on the screen
- Low battery indicator
- Over range indicator
- Peak hold function
- MAX/MIN calculations
- Relative mode
- Non-contact votlage detector built in
- AC/DC voltage measurements to 600V
- Resistance measurements to 110MΩ
- Frequency measurements to 110MHz
- Capacitance testing to 110mF
- Temperature measurements to 1000°F
- Diode/continuity testing
Applications:
- Measure flame safety control current
- Test run and start capacitors and motors
- Measure motor run current and capture peak motor start up amperage
- Measure heat anticipator current
- Determine thermocouple voltage
- Test line and control voltages
- Measure heating element resistance
- Measure air temperature in ducts
- Test for the presence of voltage in circuits without contacting the circuit
- Measure temperature differential using relative mode
About TPI Europe
Since 1997, TPI has been striving to offer the latest technology at the most affordable price to technicians, contractors, engineers and others seeking value-based test and measurement instruments. Our mission is to become the leading independent manufacturer and supplier of low cost high-performance industrial instrumentation.
Headquartered in the heart of the “Silicon Forest” in Beaverton, Oregon, TPI combines innovation, performance, customer service and high-value in products which include: Vibration, Combustion, Pressure (manometers), Temperature, Combustible gas, Digital Multimeters, Clamp Meters, IAQ, specialty test and measurement instruments, and a wide range of accessories.
| Manufacturer | TPI Test Products International | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Short Description | TPI 275 Digital Clamp Meter
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Product Stock Status | Next Day Delivery (subject to availability) | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Updated January 2024
Please note, our cut-off time is 2:00pm
Orders requiring calibration
Whilst we take the greatest care to get all orders dispatched and delivered to you in the stated time frame, orders received PM and requiring calibration may on occasion miss dispatch that day, according to the complexity of the calibration.Be assured they will ship on the next dispatch this in most cases should not add more than 24 hours to your delivery.
Bank/Public Holidays
Predicted delivery times are based on regular trading days Monday to Friday. Public holidays, bank holidays and weekends are outside the usual scopeof our dispatch and subject to activities/holidays of our carriers and therefore may incur additional days lead time to your order.
*UK Mainland (Revised March 2021)
| Service | Price |
| Standard FREE 2-3 Day Courier Delivery – UK Mainland only - Zones A & B - Order value OVER £75.00 ex VAT | FREE |
| Standard FREE 2-3 Day Courier Delivery – UK Mainland only - Zones A & B - Order value UNDER £75.00 ex VAT | £4.95 |
| Next WORKING Day (excludes Saturdays, Sundays and public holidays) – UK Mainland only - Zones A & B - ANY order value - Order by 2:00pm | £7.75 |
| Saturday ANYTIME Delivery - Order by 2:00pm | £9.95 |
Delivery Surcharges
Because of the high cost of carriage, we regretfully need to apply a surcharge on all deliveries made in the following regions:
- Zones A & B - Mainland delivery rates apply.
- Zone C - Scottish Highlands (Charges are calculated at the checkout).
- Zone D - Outer Hebrides, Orkney Isles, Shetland Isles, Isle of Man, Scilly Isles, and Channel Islands (Charges are calculated at the checkout).
- Zone E - Northern Ireland (Charges are calculated at the checkout).
- Zone F - Republic of Ireland (Charges are calculated at the checkout).
Offshore Services
All offshore deliveries are a 3-4 day service as standard. This includes Channel Islands, Northern & Southern Ireland, Scottish Islands, Isle of Man and the Scilly Isles.
International delivery
International delivery charges are automatically added to your order at the checkout. For any questions regarding international deliveries please contact us at sales@isswww.co.uk
Export
All export inquiries should be directed to the export division before placement of order.
If no shipping option is available to your selected country please call us FREE on 0800 0224 060 to discuss your requirements.
All stated prices are subject to VAT at the current rate where applicable.
E&OA